Rotor Grinder for Grinding Wheel Material

In the rapidly developing area, many people have a certain understanding of Rotor Grinder for Grinding Wheel Material, and crusher technology is in an absolute leading position in the industry.

In terms of airflow milling, it is important to understand its operational rules, which is very important because only familiarize the procedure, can operate correctly.
1. The operation rules of Rotor Grinder for Grinding Wheel Material are as follows: After the preparation before the boot receives the production order, the material is prepared. Complete the site to clean the grocery. Check whether the transportation pipes and auxiliary equipment, whether the pipelines are blocked, leak or poor sealing, whether the auxiliary equipment is intact, whether it works normally. Whether there is a phenomenon that the material is accumulated in the outer casing and the separator, if the accumulated material is required. Whether the bearing is lubricated, whether it is lubricated in an appropriate place. Check if all pipes, fastening bolts, washers, spindles, and instruments are intact, normal and flexible.
Second, Rotor Grinder for Grinding Wheel Material, start the motor, control the current and time at starting, so that the device can start running. When the equipment is operating normally, the feed speed can be adjusted according to the properties of the material. Uniform continuous feed should not be large or small, thereby affecting the separation effect of the grinding machine, making the machine easily malfunction. During operation, if an abnormality occurs, stop checking immediately before the failure continues.
Third, Rotor Grinder for Grinding Wheel Material The main procedures are as follows: After the material in the grinding machine housing is completely pulverized, it should stop the feed and turn off the motor. After the machine is idling for 3 minutes, press the stop button to stop the machine. When the machine is completely stopped, open the check door and check the wear of the vessel. Fill in the corresponding production record, update the device status flag, which is convenient for the next use.


ALPA Composite Powder Rotor Grinder for Grinding Wheel Material Case Sharing: This customer is a renewable resource company, which needs to select a different granular selection of composite powder, and it is necessary to select less than 30μm ultrafine powder. Investigate a number of domestic grading equipment manufacturers, did not find the right equipment, and finally found the right equipment in our AlPa, and selected our vertical grading machine equipment. Product particle size: D97 ≤ 30μm hour yield: 80T
Welcome major composite powder manufacturers to visit, incompetent experiments.
Rotor Grinder for GRINDuring the problem of dust leakage, Ding Wheel Material, can be processed from the following aspects

1. Install the dust filter. For the dust generated by the high-temperature pulverizer, foam dust removal, wetting agent dust removal, ultrasonic atomization technology, composite filter bag dust removal, folding dust release bag, wide spacing electric precipitator dust removal. The user can also consider the overall performance of dust removal, so combined dust removal is used.

2. Due to the mild leakage during the production process, the dust will appear, causing pollution to the work area. Therefore, the user needs to guarantee the sealing property of the pneumatic grinding machine.
3, increasing the humidity of the equipment operation area, strengthening ventilation, storing fire equipment, avoiding a large amount of dust inhaling the harm caused by the human body.

4. Production enterprises should be equipped with corresponding protective supplies as required for air compressor operators. The operators should also wear protective supplies in accordance with regulations.

5, do a good job in the maintenance and management of existing dust equipment, guarantee its normal operation and use dustproof. The maintenance management of high temperature crushers seems simple, and actual operation requires good attitude and habits.


Shandong Alpa focused on the production, development, sales of powder engineering equipment and other powder engineering equipment, etc. Three parts are composed, collecting gas flow, airflow grading, mechanical pulverization, flexible realizing airflow smashing, airflow classification, mechanical pulverization, suitable for 325 mesh -10000 mesh (45μm), suitable for all kinds of crushing scenes, from scientific research The institutions, colleges and universities laboratories, new products, new materials, new materials to the factory research and development and trials. It is necessary to make the device selection according to the actual needs. Welcome new and old customers to come to consult!