Rod Pin Grinder of Fe-based Amorphous

Because Rod Pin Grinder of Fe-Based Amorphous are widely used in all walks of life, research and development of classified machines at home and abroad pay great attention. In the current market, there is a great development space.

Rod Pin Grinder of Fe-based Amorphous is applied to the ultra-fine pulverization of the material. After the material is extracted, the nature of the powder will change, and it is high viscosity after being affected. Cake. Powder is extremely prone to aggregation in the feed opening, pulverizing cavity and exhaust pipe, requires special treatment processes and specific design.

Shan dong alpa design and developed materials were significantly effective in the crushing of materials.
ROD PIN Grinder of Fe-based Amorphous Compressed Gases The high-speed jets generated by the feed nozzle The material particles in the bucket are introduced into the disc pulveration chamber 3, and several jet spray is provided around the pulverization chamber. The high-speed fluid is injected in a direction in which the high-speed fluid is sprayed in the pulverization chamber. The coarse particles in the opposite ultra-high-speed swirls in the superiospantial cyclone generate hit and friction in the intersection, and the particles were quickly pulverized.

When the particles are pulverized to the pulverizing particle size below the pulverized particle size, the centrifugal force of the particle movement is reduced, and the pulverization is separated from the center of the center, and is collected from the center outlet. Such a pulverizer, the motion of the particles can be decomposed into two components in both directions. In one direction, the direction of movement of the particles is substantially consistent, and there is no significant impact pulverizing effect, and only in the other direction, the particles are opposite, and the particles produce effective impact.
Therefore, this impact of the intersection is limited, and the energy of ultra-high-speed moving particles is not fully utilized, so the production energy consumption is still high.

AlPA Composite Pin Rod Pin Grinder of Fe-Based Amorphous Case Sharing: This customer is a cement manufacturer, wants to deliver the cement filler composite powder, select the composite powder of the appropriate particle size section, thus Enhance the performance of the cement. Investigate the domestic powder equipment manufacturer, and finally chose our AlPA classifier to achieve the pursuit of large capacity, and ensure the particle size of the powder.
Case parameters:

Powder particle size: D50: 6.8μm

Hour Yield: 25T
For powder production companies, customized production, non-standard customized products are an advantage . The demand for each company is different. Therefore, the non-standard custom of powder equipment has gave birth to the powder equipment, and the ALPA of Shandong is a powder equipment non-standard custom enterprise. We set up for TaiwanThe comminution equipment is a good case. Enterprises that have powder equipment customization needs to contact us.
For the long-term \"health\" of the equipment, we need to take some steps to protect them again.
1. First, the gap of the hammer screen can be adjusted: the friction on the screen changes varies from the distance between the material and the screen, and the friction is different. Improve the hammer speed and hammer material efficiency by adjusting the hammer net gap. However, during the production process, the screens they use are different, the raw materials are different, the hammer screening gap needs to be adjusted; in the crusher, the crusher is not very good at the beginning, but after a period of time Work, the particles inside the crusher also changes; in the grinding machine parts, the hammer head is easily worn, and the gap between the hammer head and the screen is increased, and the yield is also declining, it is difficult to maintain.
Of course, in order to test the yield of a crusher, for some of the raw materials, for some screen holes, in order to determine the appropriate hammer sieve gap and suction, the useful life of the screen and the hammer can be obtained in a short time. Very high grinding efficiency data. However, in the production of feed grinding, such specific measurement data, according to the operator's work experience, the technical content of the crusher itself is two things. People with enrichment of experience and labor experience also require higher operating costs. When the hammer is worn, the gap between the hammer and the sieve increases, the friction is reduced, and the abrasive efficiency is lowered.

2. Rod Pin Grinder of Fe-based Amorphous mainly requires a reasonable use of reverse glitch: mainly to rush the side hair of the screen into the interior, greatly increase the friction, but this method is not used for a long time. After the globi polishing, the efficiency is lowered. It lasts for 30 minutes to 1 hour.

3. Put the friction piece into the Rod Pin Grinder of Fe-based Amorphous: The friction piece has the effect of the material ring, but the effect is limited. First, the teeth of the friction plate are in front of the hammer head, the friction surface is small, and the hammer is long-lasting; if the sieve area is too small, the output screen area will be reduced.
For any device, everyday maintenance can be performed, it can ensure that the equipment can run for a long time, so everyday maintenance of ROD PIN GRINDER OF Fe-Based Amorphous is critical.


Weifang AlPa airflow crusher price, our company with large test workshops can meet different customers 1: 1 industrialized test finished particle size from 100 mesh-6000 points, mainly for new energy Materials and other industries